
What's Inside the 1.2 kg Box
Adaptive Glass Mapping
Built-in edge sensors map your pane in 3 seconds. Whether it is a 4x4 ft casement, an 8 ft picture window, or a non-rectangular bay, ClearVista plots a bow-pattern path before moving. The route adjusts in real time on obstacles (frame, decal). No phone pairing.
Triple-Layer Safety Net
A 150 kg (330 lb) braided steel cable, a 20-minute UPS battery, and a real-time pressure-drop alert work together. If suction dips below safe hold, the alarm sounds in under 1 second and the unit holds position. If power cuts, the UPS keeps the seal active for 20 minutes.
Physical Remote - No App Required
The included infrared remote controls start, stop, pause, and direction. No phone pairing. No Wi-Fi. No app login. No firmware update can brick it. It works the moment you press the button. LED lights on the unit show battery level and cycle progress.
5,600 Pa - Pro-Class Suction Power
The 5,600 Pa motor generates 50 N of downward pressure on dual rotating microfiber pads at 16 cm/second. That matches the pro-class suction tier most homeowners pay $449-$499 for. Hard water spots, pollen film, and bird strike lift in one to two passes. No Wi-Fi signal needed.
What our 17,000+ Customers say
Based On Real and Honest Experiences
Frequently Asked Questions
Will ClearVista fit my window size and type?
Will ClearVista fit my window size and type?
Yes, on standard framed glass. ClearVista's edge sensor reads the frame perimeter, then auto-calibrates suction and bow-pattern path. Works on casement, double-hung, picture, bay, and floor-to-ceiling panes (with frame). Minimum pane size 50 cm x 50 cm. For fully frameless or butt-jointed glass, see Q12 below.
Is it safe for upper-floor or high-rise windows?
Is it safe for upper-floor or high-rise windows?
Yes, up to 4 stories with proper tether anchoring. Three safeguards run in parallel: 5,600 Pa continuous suction (primary hold), 150 kg-rated tether (anchored inside your room), and a 20-minute UPS battery (keeps the seal active if power cuts). For high-rise above 4 stories or floor-to-ceiling balcony glass, contact support.
How long does a full cleaning cycle last?
How long does a full cleaning cycle last?
Most standard residential panes (3-6 ft) clean in 8-12 minutes per window. A typical 14-pane two-story home takes 90 minutes start to finish. ClearVista runs from a 4-meter cord (no charging cycle to track); the 20-minute UPS battery keeps the seal active if your power flickers mid-cycle. No app, no phone unlock.
Can it remove tough stains like bird droppings or hard water marks?
Can it remove tough stains like bird droppings or hard water marks?
Yes. The 5,600 Pa motor applies 50 N of pressure through dual rotating microfiber pads at 16 cm/second. That replicates the circular scrubbing of a pro detailer. Bird strike, hard water mineral deposits, pollen film, and tree sap lift in one to two passes. For very thick caked dirt, pre-spray glass with water once.
How noisy is ClearVista during operation?
How noisy is ClearVista during operation?
ClearVista runs at 40-60 dB on standard residential glass - quieter than a normal conversation (60 dB) and well under the WHO daytime noise limit (55 dB outdoor). Run it during conference calls, nap time, or early mornings without disturbing anyone. On rough or single-pane glass, expect 55-65 dB.
How often should I swap out the cleaning pads?
How often should I swap out the cleaning pads?
The microfiber pads are machine-washable and last 50+ wash cycles. For a typical 12-pane home cleaned monthly, replace pads every 2-3 months. Spare 2-pad sets cost $15 (no proprietary subscription). The pads click on and off in 5 seconds. Keep a spare set on the shelf.
Does setup require an app or Wi-Fi pairing?
Does setup require an app or Wi-Fi pairing?
No app, no Wi-Fi, no account. First setup takes 5-10 minutes - anchoring the safety tether is the main step (loop it around a door handle, table leg, or radiator). After that, every cleaning session starts in under 2 minutes: place unit on glass, press suction button on the remote, wait 3 seconds, press start.
What happens if the robot encounters an obstruction?
What happens if the robot encounters an obstruction?
ClearVista's pressure sensor monitors suction 200 times a second. If hold drops below safe levels (decal, security film, ice buildup), the unit halts within 1 second, the alarm beeps, and the suction motor locks at maximum until you arrive. The tether catches it as a third backup if all else fails.