{"product_id":"thermalume-filament-dryer-box","title":"Thermalume","description":"\u003cp\u003ePopping, spitting and stringing turn a good evening into a failed print. This dual-spool dryer warms both spools with circulating hot air and feeds filament to your printer. Set it, start a long print, and go to bed without hovering over the nozzle.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003ePrint on dry filament without unloading spools\u003c\/li\u003e\n\u003cli\u003eKeep two spools ready for back-to-back prints\u003c\/li\u003e\n\u003cli\u003eCut the popping and stringing from wet filament\u003c\/li\u003e\n\u003cli\u003eKeep filament dry between drying runs\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eEven drying across both spools\u003c\/h3\u003e\u003cp\u003eWarm air reaches both spools evenly, thanks to a large heating plate and a built-in blower fan with 360° hot-air circulation.\u003c\/p\u003e\u003ch3\u003eSpools stay dry between runs\u003c\/h3\u003e\u003cp\u003eA silicone seal strip and insulation cotton keep filament protected from moisture, even when the dryer is powered off.\u003c\/p\u003e\u003ch3\u003eLeave it running up to 24 hours\u003c\/h3\u003e\u003cp\u003ePick any heating time from 0 to 24 hours and follow the countdown on the display, so a long cycle runs without you.\u003c\/p\u003e\u003ch3\u003eFits beside your printer\u003c\/h3\u003e\u003cp\u003eSits on your desk next to the printer, at 200 x 250 x 235 mm (7.9 x 9.8 x 9.3 in) and about 1.75 kg (3.86 lb).\u003c\/p\u003e\u003ch3\u003eHow it works\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eLoad up to two spools onto the stainless steel rods inside.\u003c\/li\u003e\n\u003cli\u003eClose the sealed lid, then set 45 to 50°C (113 to 122°F) and your timer.\u003c\/li\u003e\n\u003cli\u003eA heating plate and fan circulate hot air around both spools.\u003c\/li\u003e\n\u003cli\u003eFeed filament to your printer through a PTFE tube, or leave it sealed for storage.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat's in the box\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eK-02 dual-spool filament dryer x1\u003c\/li\u003e\n\u003cli\u003eUser manual x1\u003c\/li\u003e\n\u003cli\u003ePower adapter with US plug x1\u003c\/li\u003e\n\u003cli\u003ePTFE tube x4\u003c\/li\u003e\n\u003cli\u003eRotating shaft x1\u003c\/li\u003e\n\u003cli\u003ePlugs x6\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFAQ\u003c\/h3\u003e\u003cp\u003e\u003cstrong\u003eIs 50°C (122°F) hot enough for my filament?\u003c\/strong\u003e\u003cbr\u003eAdjustable from 45 to 50°C (113 to 122°F), a range suited to everyday PLA and PETG. Check the temperature guidance printed on your spool to match it to your filament.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eCan I print straight from the dryer while it runs?\u003c\/strong\u003e\u003cbr\u003eYes. Filament can feed to your printer through a PTFE tube from a fitting on the lid while the spool stays inside, so there is no unloading. Four PTFE tubes and six plugs come in the box.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWill my 1 kg (2.2 lb) spools fit?\u003c\/strong\u003e\u003cbr\u003eStandard 1 kg (2.2 lb) spools fit, two at a time. Each spool can be up to 200 mm (7.9 in) across and 73 mm (2.9 in) wide, so measure your spool's diameter and width to check.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eDo I need to add desiccant?\u003c\/strong\u003e\u003cbr\u003eThe built-in desiccant box holds your own desiccant for extra moisture control between runs. The heating plate and fan do the main drying.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWill it keep my spools dry when it's switched off?\u003c\/strong\u003e\u003cbr\u003eThe sealed structure, with a silicone seal strip and insulation cotton, is built so filament stays protected from moisture even when powered off. Keep the lid closed and the plugs in the fittings.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat comes in the box?\u003c\/strong\u003e\u003cbr\u003eOne K-02 dual-spool filament dryer, one user manual, one power adapter with a US plug, four PTFE tubes, one rotating shaft and six plugs.\u003c\/p\u003e","brand":"PrimyDeals","offers":[{"title":"Default Title","offer_id":49750600908955,"sku":"PD-thermalume-filament-dryer-box-1","price":339.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0746\/1712\/7067\/files\/filament-dryer-box__p6_v1.png?v=1791476026","url":"https:\/\/primydeals.com\/products\/thermalume-filament-dryer-box","provider":"PrimyDeals","version":"1.0","type":"link"}