{"product_id":"slowlark-pwm-controller","title":"Slowlark","description":"\u003cp\u003eUpgraded ride-on too fast, fan too loud, pump blasting at full power? This PWM controller puts the speed in your hand with a twist of the knob. The ride-on rolls off at a pace you chose, and the shop fan hums along while you work.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eSlow a too-fast ride-on to your pace\u003c\/li\u003e\n\u003cli\u003eHalt your motor from the board itself\u003c\/li\u003e\n\u003cli\u003eHear less whine from your motor\u003c\/li\u003e\n\u003cli\u003eWire it right with labeled terminals\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eHalt the motor from the board\u003c\/h3\u003e\u003cp\u003eStop or brake with one slide of the switch. The on-board switch has Run, Stop and Brake positions, and must sit on Run to drive.\u003c\/p\u003e\u003ch3\u003ePut the dial where your hand reaches\u003c\/h3\u003e\u003cp\u003eMount the knob away from the board. The potentiometer separates on a cable of about 15 cm (5.9 in).\u003c\/p\u003e\u003ch3\u003eMount it covered and fixed in place\u003c\/h3\u003e\u003cp\u003eScrew it down with the board covered. The perforated metal case has side flanges with screw holes.\u003c\/p\u003e\u003ch3\u003eFuse included, ready to wire\u003c\/h3\u003e\u003cp\u003eGet a fuse in line from the start. The holder takes a replaceable car-type blade fuse on a 30 cm (11.8 in) red 12 AWG wire.\u003c\/p\u003e\u003ch3\u003eHow it works\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eConnect your DC power supply to the P+ and P- input terminals.\u003c\/li\u003e\n\u003cli\u003eWire your brushed motor to M+ and M-. Swap the two wires to reverse direction.\u003c\/li\u003e\n\u003cli\u003eSlide the switch to Run and twist the knob to set your speed.\u003c\/li\u003e\n\u003cli\u003eSlide the switch to Brake or Stop when you want the motor to halt.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat's in the box\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e1 PWM controller with potentiometer knob\u003c\/li\u003e\n\u003cli\u003e1 inline fuse holder with fuse and 30 cm (11.8 in) red wire\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFAQ\u003c\/h3\u003e\u003cp\u003e\u003cstrong\u003eDoes it work with brushed or brushless motors?\u003c\/strong\u003e\u003cbr\u003eBrushed DC motors only. It will not drive brushless motors, and it cannot take AC input. You also need your own DC power supply, since one is not included.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWill it handle my voltage and power?\u003c\/strong\u003e\u003cbr\u003eYes for most brushed DC setups from 7 to 70V. Higher voltage means less usable current, so leave margin and stay within the limit for your voltage, for example 24V up to 400W. Others: 12V 300W, 48V 450W, 60V 500W.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWill it slow down my Power Wheels after a tool battery upgrade?\u003c\/strong\u003e\u003cbr\u003eIf the motor is brushed DC and your battery falls in the 7-70V range, the knob lets you turn the speed down. Stay within the power limit for your voltage, for example 24V up to 400W.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhy does my fuse keep blowing?\u003c\/strong\u003e\u003cbr\u003eHigher voltage means less usable current, so keep to the power limit for your voltage, for example 24V up to 400W. Check your input polarity, since reversed polarity damages the controller. The blade-type fuse is replaceable.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eHow do I wire it without instructions?\u003c\/strong\u003e\u003cbr\u003eInput goes to P+ and P- from your DC supply, and getting the polarity wrong damages the controller. The motor goes to M+ and M-, and it does not care about polarity. Swap its wires to reverse direction.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eCan I use it with a 12V fan or pump?\u003c\/strong\u003e\u003cbr\u003eYes, if the motor is brushed DC and stays within 12V up to 300W. The knob sits on a detachable cable of about 15 cm (5.9 in), so you can place the dial where it suits your fan or pump.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWill it fit in my ride-on toy or project?\u003c\/strong\u003e\u003cbr\u003eThe module measures 90 x 59 x 34 mm (3.54 x 2.32 x 1.34 in). Measure the free length, width and height of your space, and leave room for the side flanges and the knob cable.\u003c\/p\u003e","brand":"PrimyDeals","offers":[{"title":"Red PCB","offer_id":49841419813019,"sku":"PD-slowlark-pwm-controller-1","price":119.99,"currency_code":"USD","in_stock":true},{"title":"Green PCB","offer_id":49841419845787,"sku":"PD-slowlark-pwm-controller-2","price":119.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0746\/1712\/7067\/files\/pwm-controller__p5_v3.png?v=1792219411","url":"https:\/\/primydeals.com\/products\/slowlark-pwm-controller","provider":"PrimyDeals","version":"1.0","type":"link"}