{"product_id":"glideglow-hot-wire-foam-cutter","title":"GlideGlow","description":"\u003cp\u003eKnife cuts crumble and cheap cutters quit mid-project. This 18W hot wire kit melts a path through low-density foam, so your lettering or prop gets cut and you move on to painting.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eMelt a clean path through low-density foam\u003c\/li\u003e\n\u003cli\u003eCut, carve and punch holes with one kit\u003c\/li\u003e\n\u003cli\u003eGet back to cutting after a snapped wire\u003c\/li\u003e\n\u003cli\u003eMake signs, props and Halloween costumes\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eStart cutting within seconds\u003c\/h3\u003e\u003cp\u003eNo long wait before your first cut. The heating tube reaches 150 °C (302 °F) in 10-15 seconds.\u003c\/p\u003e\u003ch3\u003eSweep wide curves in one pass\u003c\/h3\u003e\u003cp\u003eFollow big, flowing lines in a single move with the bow head, 18 cm (7.1 in) wide and 8.5 cm (3.3 in) deep.\u003c\/p\u003e\u003ch3\u003eDraw small letters and fine lines\u003c\/h3\u003e\u003cp\u003eTrace tight lettering and detail with a 2 mm (0.08 in) stainless steel heating rod.\u003c\/p\u003e\u003ch3\u003eCarry on after a snapped wire\u003c\/h3\u003e\u003cp\u003eSwap in fresh wire and get back to cutting, with 10 m (32.8 ft) of heating wire included in the kit.\u003c\/p\u003e\u003ch3\u003eHow it works\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003ePlug in the adapter and slide the switch on. The green light shows it's powered.\u003c\/li\u003e\n\u003cli\u003eWait 10-15 seconds while the heating tube comes up to cutting temperature.\u003c\/li\u003e\n\u003cli\u003eGuide the tip slowly and let the heat melt a clean path through your foam.\u003c\/li\u003e\n\u003cli\u003eSwitch off, rest the pen on its stand, and let it cool before you touch it.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat's in the box\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eCutter handle with on\/off switch\u003c\/li\u003e\n\u003cli\u003eShort straight heating tip\u003c\/li\u003e\n\u003cli\u003eLong straight heating tip\u003c\/li\u003e\n\u003cli\u003eBow heating tip\u003c\/li\u003e\n\u003cli\u003eMarker pen\u003c\/li\u003e\n\u003cli\u003eStand\u003c\/li\u003e\n\u003cli\u003e10 m (32.8 ft) of heating wire\u003c\/li\u003e\n\u003cli\u003ePower adapter (US plug)\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFAQ\u003c\/h3\u003e\u003cp\u003e\u003cstrong\u003eWho is this kit for?\u003c\/strong\u003e\u003cbr\u003eHobbyists, sign makers, model builders and costume crafters who work in low-density foam. It cuts, carves and punches holes, so letters, props, Halloween costumes and DIY projects are all fair game.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat kinds of foam can I cut with it?\u003c\/strong\u003e\u003cbr\u003eIt's built for low-density foam such as EPS polystyrene, EPP, sponge, pearl cotton and KT board. Guide the tip slowly and let the heat melt the path through the foam.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eCan it cut XPS or very dense foam?\u003c\/strong\u003e\u003cbr\u003eThis kit is made for low-density foam such as EPS polystyrene, EPP, sponge, pearl cotton and KT board. For dense or hard foam, test a scrap piece first and guide the tip slowly.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eHow do I clean the tip after cutting?\u003c\/strong\u003e\u003cbr\u003eLet the tip cool, then wipe it with a damp sponge. This clears melted foam and helps stop oxide building up and hardening on the heating tip. Do it after each session so the tip is ready next time.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eHow long can I run it at a time?\u003c\/strong\u003e\u003cbr\u003eGive it a rest after 30 minutes of continuous use. Switch it off, set it on the stand and let it cool. Plan a short break into longer projects and you'll be ready to keep cutting.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eHow do I swap tips without burning myself?\u003c\/strong\u003e\u003cbr\u003eSwitch the cutter off and let it cool completely before you touch or change any part. The bow head is a separate piece held by 3 screws and fits the same handle socket as the straight tips.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWill the plug work with my outlet?\u003c\/strong\u003e\u003cbr\u003eWe sell the US plug version, rated 100-240 V AC, so it runs on standard US 120 V mains. It's a corded kit with a power adapter and no battery, so plan to work within reach of an outlet.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eDo I need ventilation when I cut?\u003c\/strong\u003e\u003cbr\u003eWork in a well-ventilated space, as with any hot foam tool. Keep a steady pace while you cut, then switch the cutter off and let it cool on its stand when you're done.\u003c\/p\u003e","brand":"PrimyDeals","offers":[{"title":"Default Title","offer_id":49770747363483,"sku":"PD-glideglow-hot-wire-foam-cutter-1","price":159.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0746\/1712\/7067\/files\/hot-wire-foam-cutter__p1_v1.png?v=1791643547","url":"https:\/\/primydeals.com\/products\/glideglow-hot-wire-foam-cutter","provider":"PrimyDeals","version":"1.0","type":"link"}